Evening all, just looking for a bit of insight.
Im looking to change out the standard bumpers and end caps on my mk3. I was just wondering if anyone has done this before and if so, what parts did you use?
Thanks in advance.
Mk3 bumper
-
- Posts: 10
- Joined: Thu Apr 04, 2019 4:04 pm
- Car(s): 1987 Ford Capri 1.6 Laser & 2017 Nissan X-Trail 1.5 Tekna
-
- Donator
- Posts: 894
- Joined: Sun Jan 15, 2017 3:54 pm
- Car(s): Just sold 1983 2.8 Injection 5 speed. Currently restoring another classic Previously owned 2 Capris. Likely to own another at some point
Re: Mk3 bumper
When you say change them out do you mean replace the existing Mk3 bumpers with better examples of the same parts or are you looking for ideas of alternatives that will change the look of your car such as Mk 2 bumpers, Tickford type grp bumpers, large US Federal bumpers ?
- Noel
- Donator
- Posts: 530
- Joined: Thu May 19, 2011 7:57 pm
- Car(s): Capri 2.8i
Range Rover
M140i - Location: Twickenham
Re: Mk3 bumper
Bet that is the first time anyone has ever suggested that, on any forum, about any car, ever.
Re: Mk3 bumper
Dont know.PintoPunk91 wrote: ↑Sun Mar 29, 2020 11:58 pm Evening all, just looking for a bit of insight.
Im looking to change out the standard bumpers and end caps on my mk3. I was just wondering if anyone has done this before and if so, what parts did you use?
Thanks in advance.
I'm the one who leaves all those shoes in the carriageway.
-
- Posts: 10
- Joined: Thu Apr 04, 2019 4:04 pm
- Car(s): 1987 Ford Capri 1.6 Laser & 2017 Nissan X-Trail 1.5 Tekna
Re: Mk3 bumper
Something like the mk2 bumpers. Ideally something without the end caps. And no to the US spec stuff.
-
- Donator
- Posts: 894
- Joined: Sun Jan 15, 2017 3:54 pm
- Car(s): Just sold 1983 2.8 Injection 5 speed. Currently restoring another classic Previously owned 2 Capris. Likely to own another at some point
Re: Mk3 bumper
Its probably worth posting up Mk2 bumpers and brackets in the Parts Wanted section.
-
- Posts: 4412
- Joined: Mon Jul 28, 2008 1:17 pm
- Car(s): 1986 Ford Capri 2.0 Laser
2004 Mazda RX8 - Location: Surrey
- Contact:
Re: Mk3 bumper
I have mk2 chrome bumpers, used the brackets for mk2 items for the rear, have a feeling the front are the same as standard mk3 ugly ones. It's pretty straightforward, just unbolt the originals and rebolt the new ones. It will leave holes in the wings unfortunately. I taped over the holes, filled it from the back, peeled the tape once dry, and painted the squares. Doesn't look too bad.
-
- Posts: 23
- Joined: Wed Apr 27, 2016 10:53 am
- Car(s): Ford capri mk1 cologne 3000 work in progress engine out
Ford Capri mk2 3000 daily driver but need a few parts to finish off
Re: Mk3 bumper
to give you an idea heres my mk2 fitted with a mk3 tailgate
ive got to repair the nearside section as it has a slight dent
ive got to repair the nearside section as it has a slight dent
-
- Posts: 10
- Joined: Thu Apr 04, 2019 4:04 pm
- Car(s): 1987 Ford Capri 1.6 Laser & 2017 Nissan X-Trail 1.5 Tekna
Re: Mk3 bumper
Aye, deffinitely go down the mk2 bumper route i think.. Need to get her roadworthy and MOT'd first. Then I've got LED Halos to fit. Busy boy after Lockdown.