Pressure regulator experience

Please restrict your questions and replies to Capri related technical issues!
Post Reply
tommyroland
Posts: 1
Joined: Mon Sep 27, 2021 2:18 am
Car(s): Ford Capri 2.0 Laser and 2.8 Injection

Pressure regulator experience

Post by tommyroland » Fri Oct 01, 2021 3:32 am

Hi, Does anyone here know the supplier of the pressure regulator? I'm having problems with hot start, changing almost everything, before starting on the injectors.
Or have experience with this for advice? Thanks!

User avatar
Peter-S
Donator
Donator
Posts: 7167
Joined: Mon Jul 28, 2008 7:57 am
Car(s): 1985 Capri 2.0
1983 Capri 2.8i
Location: Kent
Contact:

Re: Pressure regulator experience

Post by Peter-S » Fri Oct 01, 2021 7:16 am

tommyroland wrote:
Fri Oct 01, 2021 3:32 am
Hi, Does anyone here know the supplier of the pressure regulator? I'm having problems with hot start, changing almost everything, before starting on the injectors.
Or have experience with this for advice? Thanks!
You mean the warm up regulator? You can get rebuild kits, fairly straight forward job



https://www.ebay.co.uk/itm/383570487068 ... %3A2334524
ImageBanner by Peter Smith, on Flickr

User avatar
Noel
Donator
Donator
Posts: 497
Joined: Thu May 19, 2011 7:57 pm
Car(s): Capri 2.8i
Range Rover
M140i
Location: Twickenham

Re: Pressure regulator experience

Post by Noel » Fri Oct 01, 2021 10:10 am

Recon one listed in stock here:
https://www.motomobil.com/en/products/f ... 60518712-2

Or ask Southern Carburettors:
http://www.southerncarbs.co.uk/

ollyw
Posts: 2148
Joined: Tue Jul 29, 2008 6:40 pm
Car(s): 1984 B Reg 2.8i rebored to 2922cc near concours condition. Restored from near scrap condition.
1983 A Reg 2.8i Caspian Blue over Silver. Ongoing now roadworthy project from scrap condition
Location: England

Re: Pressure regulator experience

Post by ollyw » Tue Oct 12, 2021 9:36 pm

Do you need any special sealants Peter?
I bought one recently and intend to do the job over the winter. The German seller has yet to write any instructions.

I ask this as I also did a fuel distributor rebuild and for that I had to stick a bit of loctite (555?..) petrol proof sealant round the edge of the gasket. Worked a treat though as it was a seized item which I brought back to life at a reasonable cost.

User avatar
Peter-S
Donator
Donator
Posts: 7167
Joined: Mon Jul 28, 2008 7:57 am
Car(s): 1985 Capri 2.0
1983 Capri 2.8i
Location: Kent
Contact:

Re: Pressure regulator experience

Post by Peter-S » Fri Oct 15, 2021 11:28 am

ollyw wrote:
Tue Oct 12, 2021 9:36 pm
Do you need any special sealants Peter?
I bought one recently and intend to do the job over the winter. The German seller has yet to write any instructions.
No sealants on this one Olly
ImageBanner by Peter Smith, on Flickr

ollyw
Posts: 2148
Joined: Tue Jul 29, 2008 6:40 pm
Car(s): 1984 B Reg 2.8i rebored to 2922cc near concours condition. Restored from near scrap condition.
1983 A Reg 2.8i Caspian Blue over Silver. Ongoing now roadworthy project from scrap condition
Location: England

Re: Pressure regulator experience

Post by ollyw » Sun Oct 17, 2021 7:55 am

Great thankyou!

User avatar
Peter-S
Donator
Donator
Posts: 7167
Joined: Mon Jul 28, 2008 7:57 am
Car(s): 1985 Capri 2.0
1983 Capri 2.8i
Location: Kent
Contact:

Re: Pressure regulator experience

Post by Peter-S » Tue Oct 19, 2021 6:15 pm

ollyw wrote:
Sun Oct 17, 2021 7:55 am
Great thankyou!
White man speak with forked tongue!

I forgot Olly, the kit comes with a new diaphragm for the bottom of the unit. I used a general gasket sealant on that as it appeared that the original was probably sealed .
ImageBanner by Peter Smith, on Flickr

Post Reply